The best sewer hose system to store inside a rear bumper is the RhinoEXTREME RV Sewer Hoses w Swivel Fittings part # CAM39867. This system comes with caps to keep the odor contained so when you are done you can compress the hose, cap it off, and slide it into the bumper. That said, you need to store the adapter fittings separately as they won't fit inside the bumper but that is going to be the case for all of these 90 adapters. view full answer...
There isn't an install/rail kit for the B and W Turnoverball hitches that fits your 2023 Ford F-350 so there wouldn't be a way that we can recommend you install the B and W Hitch Center Section part # BWGNRC920 that you mentioned. The only way you could use this would be if you would be willing to fabricate a rail kit of some kind. Which if you were open to that the better option would be the part # BWGNRK1500 which was designed for this type of install. view full answer...
Easiest solution would be to use the Reese rail kit adapter part # RP30156 which fits the rail kit of your 2018 Ford F-350 and provides a set of industry standard rails that your Curt hitch would fit directly.
Or for a hitch to fit the rail kit of your truck directly the B and W Companion part # BWRVK3300 is basically the best option around. It fits the pucks directly and will give you what most in the RV world consider the best fifth wheel hitch you can get. This is a fixed hitch so... view full answer...
You can't go wrong with the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 16,000 lbs GTW, 1,600 lbs TW part # EQ64FR It offers the best user experience and is among the best at eliminating sway as you head down the road.
You will need the 2-5/16" Hitch Ball part # C40008 and the Thin Walled Socket for Equal-i-zer Hitches part # EQ70-00-4800 to install the ball.
These three components are all you need to get the set up installed view full answer...
To convert a 3 inch receiver opening to a 2 inch receiver accessory you will need a hitch adapter. If you are just using a ball mount I recommend the Curt Hitch Receiver Reducer Sleeves - 3" to 2-1/2" or 2" # C45408. If you are going to be using an anti-rattle device like you'd want on a ball mount I recommend instead using the Buyers Products 3" to 2" Receiver Tube Adapter # 337RTA302. This will allow you to use an anti-rattle lock on the 3 inch receiver and then use the anti-rattle... view full answer...
If your 2017 Ford F-350 cab and chassis has all of the 7-way wires ran to the rear of the vehicle but no actual connector what you would need is the part # HM40975-11998. This is a 7 and 4-way that can be wired easily to the wires you have.
I attached an install video for you to check out as well. view full answer...
Its not in our fitguide but the correct brake controller adapter to use a Tekonsha brake controller in a Ford F-53 chassis is the part # 3034-P.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. view full answer...
For your 2023 Ford Edge Titanium I recommend the Curt Trailer Hitch Receiver # C13234. This Class III hitch with a 2" receiver. It has a max gross trailer weight of 4,000 lbs and tongue weight of 600 lbs. It features a bolt-on installation and comes with a lifetime warranty.
For wiring, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C73FR is confirmed to fit your Titanium. The T-connector plugs into existing wiring so no cutting or splicing is required.... view full answer...
The Lippert frame does not necessarily indicate you have Lippert axles, but since you have the capacity and other measurements it isn't a concern. The manufacturer information for your axles would be found on your axle tag. With 2-1/4" shackles you need the MORryde Suspension Upgrade Kit # MR46ZR.
For a MORryde upgraded equalizer you need the MORryde Rubber Equalizers # MR87ZR. These are designed to work with trailers that have a 33" wheelbase which matches your measurement. They also... view full answer...
34 inch wide trailer frame indicates you have a cab and chassis F-350, which we do have solutions for that. But if you have an RV built on a F-350 frame then we don't have a fit that I can guarantee will fit since the rears of those are quite a bit different in dimensions than most vehicles and vary from motorhome to motorhome.
The # 41947 will fit a 2017 F-350 Cab and Chassis and it is a Class IV hitch though. If your Ford isn't a motorhome this would be a great option.
The other option... view full answer...
For a 5th wheel hitch that is a confirmed fit for the factory puck system in your 2018 Ford F-350 Dually, I have two options for you which will be dependant on bed length.
If you have the 6-3/4' bed then I recommend using the Demco Hijacker Autoslide 5th Wheel Hitch part # DM8550024. The best feature about the Autoslide is just that, it will automatically slide back away from the cab while making a sharp turn. This is going to ensure that you do not have contact between the cab of the... view full answer...
Check out the attached link for the instructions with operating instructions for your Demco Hydraulic Brake Actuator part # DM8758521. view full answer...
We have the Curt hitch extender that fits 2-1/2 inch hitches part # C45048 and can be trimmed down from 34 inches to 24 inches.
At 34 inches it has a capacity of 6,000 lb trailer weight and at 24 inches 8,000 lbs trailer weight. view full answer...
Since you changed out the motor on your MaxxAir MaxxFan and neither the old nor new motor are working I recommend using a circuit tester like # PTW2993 to verify that the motor is getting power.
If you find that the motor is getting power then it is likely that the operator mechanism is broken not allowing the lid to open and keeping the motor from turning on.
Let me know if the motor has power, and also send me the model number of your fan and I would be happy to recommend the correct... view full answer...
For both your 2020 Ford F-350 Super Duty and your 2021 Ford F-350 with the Hillsboro Flatbed I recommend the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness # 41157. This comes with a 10' harness so that you will be able to reach your center panel on your flatbed. You can use the OE Style 7- and 4-Pole Trailer Connector Socket # HM40975 in place of the 7-way connector that comes with the kit. view full answer...
Sounds like the brake controller is backfeeding 12 volts onto the brake light circuit of your RV. Check to see if the red wire of the controller is putting out 12 volts when all of the other wires are connected. If so, then the controller is bad and needs to be replaced.
For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller... view full answer...
For your 2017 Ford Superduty truck with 275/65-20 tires, we have a cable chain option. The Titan Chain Cable Snow Tire Chains - Ladder Pattern - Steel Rollers - 1 Pair # TC3031 are a confirmed fit. These are a great option for your tires that will require minimal clearances and will keep you legal. You will also need the tensioners # TCMA2 for a tight fit.
For better traction but still giving you that Class S rating for minimal clearance, I recommend the Titan Chain Alloy Snow Tire... view full answer...
For your 2016 Ford E-350 Cutaway there is not a custom fit trailer hitch receiver. However, that doesn't mean there isn't a fit. I recommend using the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide # C13704. I've attached a video to assist. view full answer...
To reach the connector, first locate the notch in the access panel in the center of the dash, near the passenger side. Using a trim panel puller, carefully pry the panel out and undo the locking tabs to remove the panel. You will find the mating connector behind this portion of your dashboard.
See picture for more info. For a trim panel tool we have the part # ALL648544. A small slot screwdriver will work too.
If you fast forward to the 4:45 mark of the attached linked video you can see... view full answer...
Go To Results